Professional heating, cooling & air quality services serving Texas City and surrounding communities in Texas. NATE-certified, 24/7 emergency response.
From emergency repair to planned installation, we deliver expert HVAC service across every specialty.
Sudden HVAC failures often stem from compressor lockout, blown transformer fuses, failed gas valves, or tripped high-pressure switches. Emergency repair service provides same-day response with technicians equipped to diagnose and resolve critical faults across all major heating and cooling equipment brands.
A comprehensive furnace tune-up includes combustion analysis, heat exchanger inspection, and verification of gas pressure at the manifold. Technicians clean burners, test flame sensor microamp readings, and confirm proper flue draft to maintain safe, efficient operation throughout the heating season.
A correctly sized heat pump installation eliminates the guesswork of mismatched equipment and undersized ductwork. Our technicians perform load calculations, verify airflow across the evaporator coil, and commission the system to manufacturer specifications for peak efficiency and longevity.
An annual air conditioning tune-up catches refrigerant leaks, worn contactor points, and degraded fan motors before they cascade into compressor damage. Technicians measure temperature differential across the coil, verify amp draws, and confirm proper subcooling to protect your investment.
Leaking and disconnected ductwork wastes up to 30 percent of conditioned air before it reaches living spaces, forcing your HVAC system to work harder and driving up energy costs. Professional duct repair seals joints, replaces damaged sections, and restores proper static pressure balance.
A professional HVAC inspection evaluates the complete system from furnace combustion and heat exchanger integrity to air conditioning refrigerant charge and electrical safety. Technicians document equipment age, efficiency ratings, and any code violations to give you a clear picture of system health.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
A professionally installed mini-split eliminates the energy losses associated with traditional ductwork while providing independent temperature control per zone. Technicians mount indoor heads at optimal height, route linesets with proper insulation, and commission each zone for verified heating and cooling output.
Ductless mini-split systems require specialized diagnostics for inverter-driven compressors, electronic expansion valves, and multi-zone communication boards. Our technicians resolve issues including refrigerant leaks at flare connections, blinking error codes, frozen evaporator coils, and failing fan motors.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
Maintaining safe and efficient boiler operation requires precise attention to water chemistry, flue gas temperatures, and combustion efficiency. Professional repair addresses leaking heat exchangers, malfunctioning aquastats, air-bound radiators, and ignition system failures to restore rated AFUE output.
Professional smart thermostat installation goes beyond mounting and Wi-Fi pairing. Technicians verify your system has the necessary common wire, confirm compatibility with multi-stage heating and cooling equipment, and program setpoints and schedules tailored to your household for immediate energy savings.
When your heat pump struggles to maintain temperature or runs continuously without reaching setpoint, the problem often traces to refrigerant leaks, failing capacitors, or degraded reversing valves. Skilled technicians restore rated HSPF and SEER performance through systematic component-level troubleshooting.
A dryer that takes multiple cycles to dry clothes or feels excessively hot to the touch signals a restricted vent line. Technicians clear lint accumulation using rotary brush systems and compressed air, then verify exhaust velocity meets manufacturer specifications for safe, efficient operation.
With 60,669 residents relying on dependable heating and cooling, Texas City needs HVAC contractors who can deliver at scale without losing the personal touch. KIC Refrigeration has built our reputation in the Texas City market by treating every project — from a thermostat installation to a full system replacement — with the same load calculation precision and installation quality.
Our Texas City, TX teams know the HVAC landscape inside and out. We understand which neighborhoods have aging furnaces approaching end of life, where duct systems are undersized, and which equipment performs best across the Texas climate. That local intelligence means better equipment recommendations and longer-lasting comfort for our customers.
Built on NATE certification, transparent pricing, and a guarantee that we stand behind.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
Our technicians live and work in the communities they serve. They understand local building codes, climate demands, utility rebate programs, and the HVAC challenges specific to your area. Local expertise backed by a nationwide service network means fast response and consistent quality everywhere.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
We help you select equipment with the highest SEER2, HSPF2, and AFUE ratings that fit your budget, and we install it to manufacturer specifications so you actually achieve rated efficiency. Proper charge, proper airflow, proper duct sealing — the details that turn rated efficiency into real savings.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Answers to the heating and cooling questions our customers ask most often.
HVAC repair costs in Texas City typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
KIC Refrigeration installs and services all major HVAC equipment manufacturers in Texas City including Carrier, Lennox, Trane, Daikin, Goodman, Rheem, York, Bryant, American Standard, Mitsubishi, and Fujitsu. For ductless mini split systems, we specialize in Mitsubishi, Daikin, and Fujitsu units which are the market leaders in inverter-driven technology. We are not locked into a single manufacturer or distributor, which means our recommendations are based entirely on what best fits your home size, budget, efficiency goals, and existing infrastructure. Each brand offers different warranty structures, SEER2 ratings, and feature sets — from basic single-stage units to premium variable-speed communicating systems. Our NATE-certified technicians install every unit strictly to manufacturer specifications and register all warranties on your behalf.
Most residential HVAC installations in Texas City, TX are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
A comprehensive HVAC inspection from KIC Refrigeration in Texas City covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Texas locations. For Texas City homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
We recommend professional HVAC maintenance at least twice per year for Texas City homeowners — once in spring to prepare your cooling system and once in fall to prepare your heating system. Each tune-up includes a comprehensive multi-point inspection covering filter replacement, refrigerant level verification, electrical connection tightening, thermostat calibration, condensate drain clearing, and performance testing. For the heating check, technicians also inspect the heat exchanger for cracks, test safety switches, and verify gas pressure on furnaces and boilers. Routine maintenance catches small problems — like a failing capacitor or a dirty flame sensor — before they cause complete system failures. Industry data shows that well-maintained HVAC systems last 15 to 20 years compared to 10 to 12 years for neglected equipment, and they operate 15 to 25 percent more efficiently throughout their lifespan.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"Dryer vent cleaning was quick and affordable. The technician showed me photos of the lint buildup — honestly had no idea it was that bad. Glad we got it done."
"KIC Refrigeration has serviced our commercial HVAC system for two years now. Always professional, always on time. Would not trust anyone else."
"Had three quotes for a heat pump installation and went with these guys. Best decision — the install was clean, efficient, and they handled all the permits."
Our NATE-certified crews provide HVAC service throughout the surrounding area.